*** SOLVED *** Card Keeps on Coming Back to its Original Height

[vance]

Please see my attached JPG file from Dropbox at this link:
https://www.dropbox.com/s/vrju37lnmedma ... t.jpg?dl=0

The Green Card in that image keeps on coming back to its Original Height.
Attached is the Project Demo Site in ZIP format from Dropbox at this link:
https://www.dropbox.com/s/q682ark1udje9 ... e.zip?dl=0

Any help?

[Pablo]

Firstly. when you share a project can you please remove all non-relevant content from the project?
So, if you have problem with one card then all other cards should be removed.

What exactly do I need to do in your project to see the problem?

[vance]

First of All,
My apology for your statement as follows:
"When you share a project can you please remove all non-relevant content from the project."

This is the 2nd time I received that statement from you.
Its only now that I have understood what you mean by that.

If you noticed, there are NO images in the ZIP file I sent you this time.
This means that I followed your 1st instruction to remove non-relevant content.

At least I tried my best to obey you.
I had no idea that you mean a different thing.
Only now that I know you mean the contents of the JPG file and NOT the contents of the ZIP file.
Sorry about this.

It happened that my JPG file contains everything because I just pressed PrintScreen KEY
and then opened the captured file with a graphics software.

If that is what you want, then so be it.
The next time I will share a project, I will focus only on contents related to the question.

So you asked:
"What exactly do I need to do in your project to see the problem?"

The Problem is like this:
When the 6 blue buttons were already on the same card on the screen,
I adjusted the height of the card to the short height of the buttons by using the handles.
So at first it just looked fine.

But after I have saved it and preview and then came back to the WYISWYG editor,
I saw that the card height which I had already adjusted before the preview
was now back on its original height.

I already tried adjusting the height of the card by the Card Properties on the lower right side
of the WYSIWYG interface, but nothing happened.

So the support I am asking is:
"Is there a way to have the height of the card fixed at a certain number of pixels?"
or maybe another solution as long as the issue is resolved.

[Pablo]

I think the issue is related to the row of buttons. The cards object was not designed to be used this way, so the height calculation is not correct.
Why are you using a card to create as row of buttons?

[vance]

First:
I am fascinated by the power of cards.
I really like the wyiwyg cards.

Secondly (with the following steps below):
I inserted a layer.
Then inserted a navigation bar.
Changed it to horizontal.
Then have my buttons and bookmarks.

Results:
Display was erratic.
Bookmarks went wild.

But nothing to worry Sir Pablo.
It seems that I have resolved the issue.
I cannot just remember what I did because I did a "million" things.
In short, there was no proper documentation in my part.
It is just that the problem was solved.
Finally the card stopped coming back to its original height.

[alan_sh]

Vance,

When Pablo says "remove all non relevant stuff", what he means is (my interpretation):

1. Create a new project
2. Put in the offending item (in your case the card container) and whatever it takes to reproduce the problem. So, no other pages, no master pages (unless that is the problem), no menus, no extra text etc etc etc
3. Does the issue re-occur? If so, save the project somewhere on the internet (including the WWB file and the equivalant folder) and post a link to it on this forum. If it doesn't occur, then you have a start to solve it on your own, because you have a working solution. So keep adding to it until the problem comes back - in which case, the last thing you added is the issue.

Does that help?

Alan

[vance]

Hello Alan,
My apology for having responded only now, August 6, 2020
and yet you posted this post on July 28, 2020.
What a shame. 9 days have lapsed before I have replied.

My issue had been resolved already.
Alan, how to indicate that the issue had already been solved?
So that in my post the word ***SOLVED*** will appear.

Is that word ***SOLVED*** done by the WYSIWYG system
or done manually of the ADMINS of this forum?

[Pablo]

or done manually of the ADMINS of this forum?

Correct, but you can also update the title yourself.

[vance]

How?

[Pablo]

Click 'Edit' to modify your post.